Difference between revisions of "Murrini"
(New page: Spot heat on the bead where you want the murrini to go and have the murrini at the ready held in some tweezers. Make sure you leave a bit of murrini sticking out from the ends of the tweez...) |
|||
| (6 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | + | == What are Murrini == | |
| + | Murrini are small nipped or cut section of glass picture cane. In cross section the murrini shows an image or pattern which runs down the entire length of the picture cane. Murrini are also known as murrine. The traditional and distinctive Italian decorative murrini patterns are known as Millefiore (thousand flowers). | ||
| + | |||
| + | Wikipedia entry on [http://en.wikipedia.org/wiki/Murrine murrine] | ||
| + | |||
| + | == Rough Guide to using Murrini == | ||
| + | |||
| + | Spot heat on the bead where you want the murrini to go and have the murrini at the ready held in some tweezers. Make sure you leave a bit of murrini sticking out from the ends of the tweezers otherwise your tweezers may get stuck on the base bead when you attach. | ||
| + | |||
| + | When your base bead is glowing, quickly waft the murrini in the top of the flame to warm slightly. Bring both the murrini and bead out of the flame and attach. | ||
| + | |||
| + | Hold the bead in the top of the flame whilst you heat some clear glass. Dab a small amount of clear on top of the murrini to keep the pattern from closing up when it is heated. | ||
| + | |||
| + | Slowly melt the murrini down in to the base bead. You may want to help the process along by flattening the murrini gently with a [[marver]] when it is soft. If you press down at an angle the pattern on your murrini will become distorted. Another method is to melt the entire murrini in to the base bead without pressing it at all which will make the pattern spread out further on the surface of the bead. Be careful not to let the base bead get too hot as it will begin to flow and distort your murrini. | ||
This takes a bit of practice but the results can be stunning | This takes a bit of practice but the results can be stunning | ||
| + | |||
| + | A guide from Jolene Wolfe of [http://www.kitzbitzartglass.com kitzbitz art glass] | ||
| + | |||
| + | [[Category:Tutorial]] | ||
| + | |||
| + | == Rough guide to using Starburst Murrini == | ||
| + | |||
| + | Spot heat on the bead where you want the murrini to go and have the murrini at the ready held in some tweezers. Make sure you leave a bit of murrini sticking out from the ends of the tweezers otherwise your tweezers may get stuck on the base bead when you attach. When your base bead is glowing, quickly waft the murrini in the top of the flame to warm slightly. Bring both the murrini and bead out of the flame and attach. Slowly melt the murrini down in to the base bead. You will be able to see the stripes on the edge of your murrini coming together towards the middle to form a starburst. Melt the entire murrini in to the base bead without pressing or leave partially raised, allow to cool and then cover with it clear glass. Be careful not to let the base bead get too hot as it will begin to flow and distort your murrini. | ||
| + | |||
| + | A guide from Jolene Wolfe of [http://www.kitzbitzartglass.com kitzbitz art glass] | ||
| + | |||
| + | [[Category:Tutorial]] | ||
Latest revision as of 16:10, 8 February 2009
What are Murrini
Murrini are small nipped or cut section of glass picture cane. In cross section the murrini shows an image or pattern which runs down the entire length of the picture cane. Murrini are also known as murrine. The traditional and distinctive Italian decorative murrini patterns are known as Millefiore (thousand flowers).
Wikipedia entry on murrine
Rough Guide to using Murrini
Spot heat on the bead where you want the murrini to go and have the murrini at the ready held in some tweezers. Make sure you leave a bit of murrini sticking out from the ends of the tweezers otherwise your tweezers may get stuck on the base bead when you attach.
When your base bead is glowing, quickly waft the murrini in the top of the flame to warm slightly. Bring both the murrini and bead out of the flame and attach.
Hold the bead in the top of the flame whilst you heat some clear glass. Dab a small amount of clear on top of the murrini to keep the pattern from closing up when it is heated.
Slowly melt the murrini down in to the base bead. You may want to help the process along by flattening the murrini gently with a marver when it is soft. If you press down at an angle the pattern on your murrini will become distorted. Another method is to melt the entire murrini in to the base bead without pressing it at all which will make the pattern spread out further on the surface of the bead. Be careful not to let the base bead get too hot as it will begin to flow and distort your murrini. This takes a bit of practice but the results can be stunning
A guide from Jolene Wolfe of kitzbitz art glass
Rough guide to using Starburst Murrini
Spot heat on the bead where you want the murrini to go and have the murrini at the ready held in some tweezers. Make sure you leave a bit of murrini sticking out from the ends of the tweezers otherwise your tweezers may get stuck on the base bead when you attach. When your base bead is glowing, quickly waft the murrini in the top of the flame to warm slightly. Bring both the murrini and bead out of the flame and attach. Slowly melt the murrini down in to the base bead. You will be able to see the stripes on the edge of your murrini coming together towards the middle to form a starburst. Melt the entire murrini in to the base bead without pressing or leave partially raised, allow to cool and then cover with it clear glass. Be careful not to let the base bead get too hot as it will begin to flow and distort your murrini.
A guide from Jolene Wolfe of kitzbitz art glass
